Freightliner Cascadia Cruise Control
Sign in Share More Report Need to report the video? I was thinking this is a good possibility but then again my cruise control works to bump up my idle, I'll see if I bump up the idle and push the But it still doesn't work. Still nothing. his comment is here
Took a truck shop 10 hours to figure it out. Community Links Pictures & Albums User Tagging Statistics Hash Tag Subscriptions Search Forums Show Threads Show Posts Advanced Search Google Search Go to Page... Sign in to add this video to a playlist. Sign in Transcript Statistics 319 views 0 Like this video?
Freightliner Cascadia Cruise Control
Was this reply helpful? Add to Want to watch this again later? Let me know, and if we have to, we will look into it more. Ask Your Own Heavy Equipment Question Customer: replied5 years ago. Logged michael Regular Membership Hero Member Posts: 1180 Re: engine brake/cruise control not working [ help? ] « Reply #7 on: May 28, 2007, 12:06:22 PM » TPS>Throttle Positioning Sensor....exactly the
Why is there never time and money to do it correctly but there's always plenty to do it again offroadnt is offline Quote Quick Reply post #17 of 26 (permalink) Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? That park brake switch sounds like a possibility. Freightliner Brake Switch Location The cruise should come off.
It's either dirty or needs replacing. Kenworth Cruise Control Problems The ground stud is behind the kick panel, driver side. Warner Truck Centers 2,415 views 4:02 HOW TO use engine brakes on steep downhill with auto trans in Freightliner, Kenworth, Peterbilt - Duration: 7:00. Sign in to report inappropriate content.
Sign in to add this to Watch Later Add to Loading playlists... Sterling Truck Cruise Control Problems Today 01:58 PM by CSchraefel 7 3 Attachment(s) Spring tines - pasture... Cruise control just quit. Ok, Thanks for the clarification on the clutch switch.
Kenworth Cruise Control Problems
You can change this preference below. The only real problem I found was one of the wires in the injector harness close to the ecm had a worn through spot so I heat shrinked that and everything Freightliner Cascadia Cruise Control The two most common causes for the cruise not working are the clutch petal switch and the parking brake switch. Peterbilt Cruise Control Problems Working...
Show more Loading... this content Sorry I can't be more specific but I don't have allot of experience with Peterbilt. If this is a late 2004, the DDEC5 harness cover on the front of the ECM has been known to rub the wires. Not sure what it was for. Freightliner Clutch Switch
Quote Quick Reply post #15 of 26 (permalink) Old 10-24-2011, 04:23 PM Thread Starter amishdonkeys Senior Member Join Date: Mar 2009 Location: East Sask Posts: 247 Mentioned: 0 Post(s) Working... Where is this ground stud? weblink I pull bulk tankers so I use the PTO a lot.
ADPTraining 66,270 views 5:15 46 videos Play all Automotive Diagnostic & Wiring DiagramADPTraining How to Reset the ECM - Duration: 5:51. Freightliner Air Switch Manifold It still goes into its intermittent fits of cruise and jakes not working. Remove that panel and you'll see the air system manifold.
It worked good like any other time I get it out of the shop then about 5 or 7 days it starts having fits.I believe it is a data-link problem.
Any ideas? The parking brake switch is attached to the yellow parking button behind the panel. Yes No Voted Undo Score 1 Cancel Comments: Hello,I have a 05 century with the same problem. Kenworth T800 Cruise Control Not Working Category Cars & Vehicles Licence Standard YouTube Licence Show more Show less Loading...
Loading... Loading... I wasnt quite sure how that worked being ground or what. check over here but if I happen to cycle the manual engine fan switch then the gauges come back on and the a/c compressor kicks back in. Expert: Clayton replied5 years ago.
OLDSKOOLERnWV posted Nov 13, 2016 at 12:56 PM Advice for snow and ice this winter rpangburn posted Nov 13, 2016 at 12:38 PM Dowell Express Nolan533 posted Nov 13, 2016 at Register Now In order to be able to post messages on the The Combine Forum forums, you must first register. Keep an eye out for that. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?
I would test the brake switch and see if it switches at about 3 to 5 psi (there are probably two or three so make sure you get the right one). I have been told that many different things could be the culprit, but is there a way to diagnose this and save me from throwing parts at the truck? Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Please enter your desired user name, your email address and other required details in the form below.
No Problem, I am glad it is working!!Thank you also Ask Your Own Heavy Equipment Question Customer: replied5 years ago. Transcript The interactive transcript could not be loaded.