bookread.org

Home > Cruise Control > Au Falcon Cruise Control Buttons

Au Falcon Cruise Control Buttons

Contents

Inside the servo is a diaphragm that moves to pull on the linkage. Set - should show 120 ohms and coast should show 2200 ohms...3) Speed signal isn't getting to the cruise module... Advertisement - Continue Reading BelowWHAT'S THIS THING?: The cruise control servo motor could be anywhere in the engine compartment.CONTROL ISSUE WITH YOUR SERVO There are two main components of the cruise Look for disconnected or damaged wiring to the controller or actuator, particu-larly if it's an aftermarket system, which may have been installed by someone with poor mechanical skills.Another obvious failure point Check This Out

No noticed problems with the Radio/Dash/Instuments SO far !! Check for leakage with a handheld vacuum pump. Last edited by Godzilla; 29-11-10 at 04:58 PM. The cruise control only has authority to reduce engine speed to idle.

Au Falcon Cruise Control Buttons

Cheers "Try anything once.... Powered by vBulletinCopyright © 2016 vBulletin Solutions, Inc. headlights could also be a few things. I just bought 2 new socets yesterday to fit.

You have the right idea though, start with the steering switches (the contacts in the steering wheel too), brake light switch, a tail light globe playing around, earths, shorts etc and The cruise control needs a signal from the brake light switch to be operational. This could indicate a faulty clock spring. _________________ Remember kids, the more pages of crap in your build thread, the bigger your e-penis is Top Profile Futura_011 Ba Falcon Cruise Control Not Working Motor mag Jan 2002 Wouldn't you love to say that about your car?You loosers Noboss is offline Quote post #5 of 5 (permalink) Old 12-25-03, 02:29 AM NZ feed me

Carefully pull airbag/horn pad forward and disconnect the airbag/horn electrical connections. Go to the wreckers and find a good set of switches. then following day when i turn on the car, i heard some clicking sound in the bonnet and i look into it and its coming out from the driver side of Turned the lights off and back it came and it did again when I repeated the lights on and off.

As a bare minimum, get into the boot & run a brand new earth wire off each tail-light harness' earth wire, and ground it somewhere solid. Ford Falcon Au Cruise Control Operating the buttons should always give firm clicking which indicates correct switch closing and opening. Reply With Quote 20-01-201010:43 AM #8 Mark73 View Profile View Forum Posts Private Message Senior Member Join Date Dec 2007 Location Shepparton, Victoria Age 43 Ride 93' ED Fairmont Posts 672 I stand unequivicably behind everything I say , I just dont ever remember saying it !!

Au Falcon Cruise Control Kit

doesnt set speed ??Posted: Fri Mar 13, 2009 2:36 pm Oompa Loompa Offline Age: 58Posts: 36Joined: 16th Jun 2006Location: LaidleyQLD, Australia Not sure about the AU but on the EF there I have no trouble getting 'Cruise' to display on the LCD, its just the 'SET' that's got the problem. Au Falcon Cruise Control Buttons That's normal too. Au Falcon Cruise Control Switch Ford Forums - Mustang Forum, Ford Trucks, Ford Focus and Ford Cars > The Garage - Tech Forums > Interior | Electrical | ECU > Cruise Control not working Reply Tweet

You might have an issue there. his comment is here Its pretty annoying coz I drive interstate for work sometimes also my headlights will only come on when I set them to Automatic or high beam but when I turn the Drove it or 6 hours yesterday and it worked perfectly - stopped for fuel and when i blasted off again - Nothing!!!Any help - tips - advice greatly appreciated..... _________________ Actually, it will normally drop out if the engine has to work too hard, mainly because after a while there isn't enough vacuum left to pull in the servo after sustained How To Use Cruise Control Ford Falcon

Performance Automotive Specials Fordmods Tech 6 Cylinder Workshop V8 Workshop Forced Induction Workshop Auto Electrical Forum Interior Modifications Exterior Modifications Gearbox, Suspension, Brake i dont think anything is broken.. I remember asking someone, but can not remember the answer, was something like hit the DTE button for 10 seconds, and then switch on ignition... http://bookread.org/cruise-control/freightliner-cascadia-cruise-control.html Ill try a different indicator stalk next and see how I go "Faster, faster, faster, until the thrill of speed overcomes the fear of death" ~ Hunter S.

These switches usually are normally closed switches, and close their contacts when the pedal is depressed. Press set + on the wheel... Disconnect your battery to avoid problems with airbags while working.

What was happening is the tail light cct was shorting to the brake light due to a broken stop/tail globe socket.

First disconnect the vehicles negative battery terminal and wait for at least 1 minute. Id hate to be someone owning one without some mechanical knowledge. Where is the vacuum thing located...i couldn seem to find itas I think it could be that possibly - it was working fine the other day though.... Yesterday 04:04 PM by CatSkinner 3 Performance chip.

Today 03:48 AM by R.S.LOGAN 5 1978 LTD Speedometer... also how do I switch the 'spanner' symbol on the dash off again. Thompson "Lots of power is good, more is better, and too much is perfect. navigate here Cheers, Tim _________________ 93 Red ED 5spd Manual Build ThreadPerformance: Complete AUII VCT Wiring & Power Train, Pacey Headers, 2.5" Exhaust, Exedy Clutch, DBA RotorsVisuals: FG XR Wheel, XR Front,

it doesn't set but cruise will display on the dash. Reply With Quote 30-11-10,04:20 PM #9 Godzilla View Profile View Forum Posts Visit Homepage Senior Member Join Date Jul 2008 Location Melbourne Age 52 Posts 12,371 Thanks 14,460 Thanked 6,641 Times If they are ok it may be the switch assy. It doesn't activate the brakes.

As a bare minimum, get into the boot & run a brand new earth wire off each tail-light harness' earth wire, and ground it somewhere solid. doesnt set speed ??Posted: Fri Mar 13, 2009 1:24 pm Oompa Loompa Offline Posts: 24Joined: 21st Sep 2006Ride: futuraLocation: sydneyNSW, Australia a_total_tool wrote:Check you brake lights/Light switchdo your audio controls and i did replace a bulb after the passenger side blew, with the same one but after that cruise never worked again the same did wiring to module under bonnet check ok Reply With Quote 29-11-10,04:57 PM #7 Godzilla View Profile View Forum Posts Visit Homepage Senior Member Join Date Jul 2008 Location Melbourne Age 52 Posts 12,371 Thanks 14,460 Thanked 6,641 Times

I have LED brake and Park lights on both sides but a globe in the wagon door Centre and up untill just very recently they seem to have worked normaly. I mean, if less is more, think how much more MORE is..." My Ninja ZX10r http://forums.mightycarmods.com/show...ki-Ninja-ZX10R My Ute http://forums.mightycarmods.com/show...-Falcon-XG-ute Reply With Quote 13-04-2011,06:14 PM #2 milkchicken View Profile View Forum Posts GIF Cars Share Drifting Budget Hatchbacks in the Rain Looks Like a Hoot Cars Share The Best Cars for Snow Cars Share SEMA 2016 PM Editor's Choice Awards Cars automotive projects These switches should normally not fail as they are pretty reliable and robust, however the actual buttons themselves are susceptible to dirt and grime which causes the button to stick in.

I stand unequivicably behind everything I say , I just dont ever remember saying it !! I was told but never confirmed that this was an earthing problem as it doesnt happen untill the vehicle, mostly sedans is a few years old. anyone know what it could be? As always, check the shop manual for specifics on your vehicle.Advertisement - Continue Reading BelowMany late-model cars have throttle plates connected directly to an actuator controlled by the engine management computer.